What Are Ribs in Injection Molding?

갈비 are thin, structural wall-like features extending perpendicular to a part’s nominal wall. They are primarily used to increase the stiffness and strength of a molded component without increasing the overall wall thickness.

의 맥락에서 사출 성형(IM), maintaining "uniform wall thickness" does not mean the rib is as thick as the main wall. Instead, it refers to designing the rib geometry so that the intersection point (where the rib meets the wall) does not create a massive thermal mass. If the mass at the intersection is too large, the material cools unevenly compared to the surrounding wall, resulting in 싱크 마크 or vacuum voids.

Proper rib design allows engineers to replace heavy, solid sections with lighter, "cored-out" structures, optimizing the strength-to-weight ratio¹.

What Are the Key Design Parameters for Ribs?

To achieve effective ribbing without compromising the cosmetic surface or moldability, adherence to specific dimensional parameters is required.

What Are the Advantages and Disadvantages of Ribbing?

Using ribs to achieve structural goals is generally superior to thickening the entire part, but it introduces specific tooling and processing challenges.

What Are the Common Application Scenarios?

Ribs are ubiquitous in structural plastic parts across various industries.

• 자동차 인테리어: Dashboard substructures and door panels using 아크릴로니트릴 부타디엔 스티렌(ABS) 또는 폴리프로필렌(PP) require ribs for rigidity without heavy weight.
• 소비자 가전: Housings for laptops and routers use dense rib patterns to protect internal components and manage thermal dissipation.
• Power Tools: Casings made of Glass-Filled Nylon (PA6-GF) utilize cross-ribbing to withstand high impact and torque loads.
• Battery Enclosures: Large enclosures require ribs to prevent warpage over long flat surfaces.

Step-by-Step: How to Design Ribs for Uniformity

Follow this workflow to ensure ribs provide strength without violating wall thickness guidelines.

1. Determine Nominal Wall (T): Establish the main wall thickness based on the material’s flow properties (e.g., 폴리카보네이트(PC) requires thicker walls than 폴리에틸렌(PE)).
2. Calculate Base Thickness (t):
   • For cosmetic surfaces (High Gloss): Set $t = 0.4 \times T$.
   • For structural/textured surfaces: Set $t = 0.6 \times T$.
3. 초안 각도를 적용합니다: Add 0.5° to 1.0° draft per side. Note: This will decrease the thickness of the rib as it gets taller.
4. Verify Tip Thickness: Check the thickness at the top of the rib. Ensure it is not less than 0.75 mm to allow proper venting and filling.
5. Add Base Radii: Add a radius of 0.25 × T at the base to reduce stress concentration. Avoid radii > 0.5 × T to prevent creating a "thick chunk" of plastic at the root.
6. Space the Ribs: If multiple ribs are needed, space them at least $2 \times T$ apart. If ribs are too close, the steel tool between them becomes thin and difficult to cool (thermal gate).
7. Run Simulation: 사용 Moldflow analysis³ to check for potential sink marks and volumetric shrinkage.

FAQ: Rib Design and Wall Thickness

Q1: Why is the rib thickness ratio limited to 40-60%?
This ratio manages the thermal mass at the intersection of the rib and the wall. If the intersection is too thick, it stays molten longer than the surrounding areas. As it cools and shrinks, it pulls the surface inward, creating a sink mark.

Q2: Can I use ribs on parts with high aesthetic requirements?
Yes, but the design must be conservative. For high-gloss parts (e.g., TV bezels), use a ratio of 40% or lower. Additionally, positioning ribs near corners or styling lines can help mask faint sink marks.

Q3: What is "Coring Out"?
Coring out is the process of removing material from a thick block of plastic to create a shell-like structure reinforced by ribs. This transforms a difficult-to-mold solid block into a part with uniform wall thickness, reducing cycle time and defects.

Q4: How does the draft angle affect the rib height?
Because the draft angle tapers the rib, a tall rib will eventually become too thin at the tip to fill. For example, with a 1° draft, the rib thickness decreases as height increases. This physical constraint limits the practical height of the rib.

Q5: What happens if ribs are spaced too closely together?
If ribs are too close (< 2 × T), the mold steel between them becomes very thin. This thin steel cannot accommodate cooling channels, leading to heat buildup ("hot spots"). This lengthens cycle times and can cause the part to warp.

요약

Achieving uniform wall thickness in rib design is a balancing act between structural requirements and molding physics. By adhering to the 40-60% thickness rule로 제한하여 높이를 3x the nominal wall, and applying appropriate 드래프트 각도, engineers can design parts that are strong, lightweight, and free of cosmetic defects like sink marks. Ignoring these constraints almost invariably leads to rejection due to surface imperfections or processing inefficiencies.